People who are following news connected to the destruction caused by the Liebherr L11350 super-crane that fell backward at the Grand Mosque in Makkah, KSA, may have wondered what such a crane would have looked like had the contractor (Saudi Binladin Group) stowed the machine in case of bad weather, as directed by the manufacturer. So here's a photo of what this particular model looks like when safed. Except for the lack of a back mast to the detached counterweight, this Liebherr L11350 is rigged similarly to the crane at Makkah, which was an "SDW" arrangement (Photo, Mace Ltd):
The thin, red and white structure on the far left is the luffing-fly jib, labeled in my previous post and diagram. Its latticed counterpart on the right side is the derrick mast. Normally the jib would be way up in the air, topping the boom, but it can be angled down with winches and pulleys that allow the jib angle to be changed (in crane language, "luffed") from the operator's seat - in this case, pointed so far down that the tip of the jib touches the ground. We don't know why the crane parked on the plaza by the Massa wasn't routinely parked this way. Lowering the boom and jib might have needed restoration of counterweights that had been removed, along with the need to round up operators and riggers rated to use this machine. Maybe bringing the jib to the ground would have interfered with pedestrian traffic. In general, I'm guessing, it seemed easier to leave the main boom and jib at a near-vertical angle. But easy doesn't mean safe, as I wrote in Inviting Disaster. If there's interest I'll post on the amazing, if narrow, niche of super-cranes.
Passing along this video of a helicopter crew and riggers assembling a tower atop the Incity skyscraper in Lyons, France, by raising sections on a long cable:
Whether it's short-lining or long-lining, moving external loads by cable takes extraordinary skill: to pilot the helicopter while looking far below, to keep the load from swinging and then to set the load within an inch or two of the desired spot, and to avoid tangling or hitting things along the way. While researching The God Machine I heard many stories of pilots who brought themselves down while carrying loads on cables. One of the striking sidelights in the helicopter world is that pilots have the authority to punch off a cable-slung load if they are sure it is going to cause the helicopter to crash: not a happy ending, particularly if there's a person on the end of the cable.
Following up on my thumbs-up report about the Dreamception iOS app when applied to ice photos ... Here's a before-and-after, with new Dreamception output on the right (in low resolution, here):
There are a lot of permutations given all the filters available, and the exact combination has a lot to do with whether the images are interesting or just flukey. tags: #deepdream, #icerules
About the crane disaster last month in Makkah (Mecca in its westernized spelling). A Liebherr L-11350 crawler crane tipped backward in a windstorm, killing 109 people in what forensic folks call the laydown zone. The worst area of destruction was where the 100-ton mast and jib dropped on the roof of a very long building on the east side called the Massa. The upper end of the jib crashed onto pedestrian areas on the other side of this building (photo AFP)
When the crawler crane fell over it also came close to destroying a tower crane, a Liebherr 335, also located on the east side of the Massa. Here's how the roof damage looked:
The "W"-shaped object above the Massa roof, projecting into it, is where the two jib struts join up with the upper end of the main boom, and the lower end of the jib (see below for a diagram). The jib struts provide a support for the jib. As the crane fell over backward, the two jib struts acted like twin piledrivers, smashing into the third and second floors of the Massa. Here's a link to the only public video I've seen of the crane going down (but I'm sure the Saudis have a lot of CCTV footage):
Here's a diagram of the basic components, before and after:
How big was it? As this crane was rigged (called an SDW arrangement in the manual), the tip of the L-11350's upper structure called the "luffing-fly jib") reached more than 600 feet off the ground. It's classed as a super-crane: while not the world's biggest crawler crane, it's close. The lift capacity under ideal conditions is 1,350 metric tons. It's a popular crane for refinery turnarounds and wind-farm projects. How long had it been on the plaza? More than three years. It was part of a big Saudi purchase from Liebherr in 2012. What was the crane doing there? It had been parked and inactive for some time. Details on usage are fuzzy; given past photos taken by pilgrims and posted online, the crane hadn't gotten much use lately. We're told that it was to be used again after the September 2015 Hajj, as part of ongoing expansion of the Masjid al-Haram and the Massa in particular. Here's a diagram of the location.
What do the initial reports say? Authorities have been interrogating employees of the contractor, Saudi Binladin Group, which has filed an insurance claim. While this particular windstorm was unusually powerful, the crane manufacturer says it was a mistake to park the crane with its boom at such a high angle (85 degrees), where it could catch the wind. What about the cleanup? Because the 2015 Hajj pilgrimagewas to begin less than two weeks after the wreck, work went on around the clock. Experts decided structural damage to the plaza at the base of the crane was so severe that the removal of the lower chassis (called the car body) would have to wait until after the Hajj, so this area was screened off from pilgrims. The focus was on removing the main boom and derrick mast from above the eastern plaza, and pulling the jib and jib struts off the roof -- and without causing more damage to the Massa, which is heavily used by pilgrims. If there's interest I'll post on how a team from Aramco got this done, with advice from heavy-life expert Mammoet, which I mentioned in this post about strand jacks.
